Furukawa-Sky Review No.3 (April 2007)

  • ツイートする
  • facebookでシェアする
音声で読み上げる

技術論文

Al-Mg-Si系合金の高温短時間時効挙動に及ぼす予備時効の影響
Effect of Pre-Aging on the Behavior in the Early Stage of Aging at High Temperatures for Al-Mg-Si Alloy

Full Text PDF(PDFファイルを開きます770KB)

  • 日比野 旭
    Akira Hibino
  • 佐賀 誠
    Makoto Saga
  • 佐々木 行雄
    Yukio Sasaki
  • 菊池 正夫
    Masao Kikuchi

Al-0.64%Mg-0.81%Si 合金の高温短時間時効挙動に及ぼす予備時効の影響を硬さ測定,電気抵抗測定,示差走査熱量計測定および透過電子顕微鏡観察を用いて調査した。高温短時間時効挙動は予備時効によって大きく影響される。約343K 未満の温度で予備時効すると,予備時効中にはG.P.I ゾーンが形成され,このG.P.I ゾーンは448K時効初期にも残存する。その結果, 448K,1.8ks高温時効後には, G.P.I ゾーンとβ”相が共存し,β”相の析出密度が低くなり,硬さ上昇量は小さくなる。一方,約343K 以上で予備時効すると,予備時効中にβ”相の核が析出し,448K 高温時効処理によって微細かつ高密度な析出組織が形成され,大きな硬さ上昇が得られる。したがって,Al-Mg-Si 系合金において大きな塗装焼付硬化性を得るためには,塗装焼付処理前のG.P.I ゾーン形成を抑制することが重要である。

Effect of pre-aging on the behavior in the early stage of aging at high temperatures for Al-0.64%Mg-0.81%Si alloy has been studied by means of hardness measurement, electric resistivity measurement, differential scanning calorimetry and transmission electron microscopy. Pre-aging temperature influenced the subsequent aging behavior at high temperatures. G.P.I zones were formed during the pre-aging below about 343K, which were stable and remained in the early stage of the subsequent aging at 448K. Therefore, G.P.I zones coexist with the β” phase in the alloy aged at 448K for 1.8ks after pre-aged below about 343K, and the distribution of the β” phase is sparse. This leads to decrease in hardness. On the other hand, nuclei of the β” phase were directly formed during the pre-aging above 343K. And the microstructure is fine and dense in the alloy aged at 448K for 1.8ks after pre-aged above 343K, which leads to the higher hardness. In order to get higher paint bake hardenability for the Al-Mg-Si alloy, it is important to suppress the formation of G.P.I zones before the bake hardening treatment.

技術論文 / Technology Articles

  1. Al-Mg-Si系合金の高温短時間時効挙動に及ぼす予備時効の影響
    Effect of Pre-Aging on the Behavior in the Early Stage of Aging at High Temperatures for Al-Mg-Si Alloy
  2. 温間異周速圧延によるAl-Mg-Si系合金の成形性向上
    Improvement of Formability in Al-Mg-Si Alloy Sheets by Asymmetric Warm Rolling
  3. 溶解炉における電磁攪拌シミュレーションの開発
    Development of a Simulation Model for Electromagnetic Stirring in Melting Furnace
  4. 双ロール鋳造法を用いたAl-Fe-Ni系合金フィン材の再結晶挙動
    Recrystallization Behavior of Al-Fe-Ni Alloy Fin Stock Manufactured by Twin-Roll

Get Adobe Reader

PDFをお読みいただくにはAdobe Readerが必要です。
お持ちでない方はこちらからダウンロードし、ご利用ください。